You don't the permission to view this video


Ever wonder how wood is joined together to make things like picture frames and table tops? While we’ll leave the more sophisticated methods to professional woodworkers, there will be times as a do-it-yourselfer when knowing how to join wood will come in handy. In this video we’ll show you how.

Read Video Transcript

Ever wonder how wood is joined together to make things like picture frames and table tops? While we’ll leave the more sophisticated methods to professional woodworkers, there will be times as a do-it-yourselfer when knowing how to join wood will come in handy.

Today we’re going to look at four different types of basic wood joints, including the pocket hole screw joint, the biscuit joint, the half-lap joint and the simple edge glued joint. These are some simple wood joinery methods that you’ll be glad you have in your basic woodworking repertoire. So let’s get started.

One of my favorite ways to join wood is using something called pocket screws. This type of joint is great for butt joints or miter joints. The pockets are made using this special drill bit and this pocket hole jig. First, you set the depth of the jig to the thickness of the wood that you’re drilling into. Here, we’re setting it to ¾". Then you set the collar on the drill bit to the proper depth using this chart on the jig. Again, we’re setting it to ¾", which is the thickness of the wood we’re working with. We align the step of the bit with the mark, not the tip. Then we’ll tighten the collar with an Allen wrench. Secure the wood into the jig following the manufacturer’s instructions. Now, simply drill through the collar holes in the jig to create the pockets in the bottom of the wood. Here you see our two holes have been drilled perfectly. These pocket screws have a flat washer-like bottom that won’t drill through the joint. The washer head will seat on the bottom of the hole. Slip the screws into the holes. After putting a little dab of glue on the joint, clamp it at the joint with this special clamping pliers. Then screw it together. It’s a tight joint that won’t come apart, you don’t need any clamps to hold it until the glue dries, and there are a variety of applications it can be used for. Pretty cool, huh?

In addition to a miter joint, you can also make butt joints, using different boards of the same thickness. Here is a butt joint made with a couple of 2x4s.

Another joinery method that is great for joining the edge of one board to the face of another is the biscuit joint. This is made using a biscuit jointer (or plate jointer, as it is also called). While this power tool takes some getting used to, once you know how to use it, you’ll turn to it time and again. It works by cutting a slot into the board that accepts this piece of compressed wood, called a biscuit. Just match the setting on the tool to the biscuit, which come in different sizes. Looking at these two pieces of wood, three biscuits should do it. Then move the biscuits out of the way and mark the center with a pencil. This mark will help in aligning the tool.

To cut the slot, you push the handle in which extends the slot cutter into the wood. After all the slots are cut, insert the biscuits to dry fit the two pieces together.

When glued into the slot, the biscuit expands and creates a very tight, very strong joint. To make this type of joint requires a variety of clamps to hold the wood in place until the glue dries. These pistol grip bar clamps are extremely useful in this type of wood joinery.

One very useful type of joint you can make that doesn’t require a special jig, a power tool or clamps is this half lap joint, which is held together by glue (or construction adhesive) and screws. This joint is made by removing half of the thickness of two boards, which are then glued together to form a joint that is the same thickness as the board. It is an extremely strong joint because of all the surface area that can accept the glue.

To make this joint you simply trace the width of the board onto the end of the other board to which it will be joined. Hold the boards perpendicular to each other then make the mark. Then measure and mark half the width of the board on both sides of the board. This is the depth that you will make your cut. Make another mark on the end of the board, exactly half way through. Then continue this line across the width of the board. With a 1" thick wood chisel, now split the wood on this line until the piece is removed. You’ll want to clamp the piece in a vice for this step. Repeat with the other board and then fit them together to test the fit. You may need to remove any additional material with the chisel. Then glue and screw the two pieces together.

The last joint we’ll make today is the edge glue joint. This is perhaps the simplest joint, where the edge of one board is glued to the edge of another. This is a common joint used to make wider boards and panels, such as table tops. It helps during the glue-up if you orient the boards alternating bark side up and bark side down. To check this, look at the end of the board to see the orientation of the growth rings. If they bend down, the bark side is up. If they bend up, the bark side is down. This enhances the stability of the panel.

Simply spread glue on the edge of one board using your finger. You might want to have a towel nearby. Then clamp them together, centering the boards on the clamp pads. Now we’ll clamp our boards with these pistol grip clamps, making sure to clean up any glue squeeze-out with a damp rag. Let it dry for a few hours and you have a wood panel that is stronger than a single piece of wood of the same width.

There you have it. While pretty basic, the wood joints we made today will get you started and will expand your basic woodworking skills. They may come in pretty hand one day, too.

Read Video Transcript

Steps

  1. 1.pocket screws

    Pocket screws are good for butt joints and miter joints. Use a pocket hole jig with a special drill bit to complete this task.

  2. 2.set depth

    Set the depth of the jig to the thickness of the wood.

  3. 3.set collar

    Set the collar on the drill bit to the proper depth.

  4. 4.clamp wood

    Clamp the wood according to manufacturer instructions.

  5. 5.Drill the holes

    Drill the holes.

  6. 6.glue joints

    Glue joints together, clamp together and gently drill the screws in.

  7. 7.biscuit joints

    Biscuit joints are great for joining the edge of one board to the face of another. Use a biscuit/plate joiner tool.

  8. 8.match setting

    Match the setting on the tool to the biscuit.

  9. 9.position

    Position the biscuit and mark the center of that position.

  10. 10.cut holes

    Cut the biscuit hole in the wood board.

  11. 11.insert and glue

    Insert biscuits, apply glue and clamp the two boards together.

  12. 12.half-lap joints

    Half-lap joints require gluing and screwing together two board halves.

  13. 13.draw

    Use a scrap piece of wood to draw a cut line.

  14. 14.draw and saw

    Draw a line halfway down the side of the board and cut with a saw to that point.

  15. 15.draw line

    Draw another half-length line on the end of the board.

  16. 16.cut

    Use either a hammer-and-wedge or a saw to cut the piece off. This will create a lap joint.

  17. 17.glue joints

    Glue lap joints together.

  18. 18.drill screws

    Drill four screws into the corners of each joint.

  19. 19.edge joints

    Edge glue joints: Alternate the boards bark-side up and bark-side down.

  20. 20.glue

    Spread glue on the edge of one board.

  21. 21.clamp

    Clamp together and wipe off excess glue.

 

Project Faqs « back to project


What type of joinery method is best for mitered corners?

When gluing miters using biscuits, you need a way to clamp the joint until the glue dries. While there are a variety of miter clamps available, the... More »

How does a biscuit joiner work?

A biscuit joiner uses a special horizontal blade that plunges into a piece of wood to create a slot for a biscuit. A biscuit is a football-shaped... More »

I am installing some door casing and want to make sure the miters are tight. What’s the best way to do this?

By installing biscuits (with a biscuit jointer) to glue the miters together and then using a corner clamp to hold the two pieces firmly in place... More »

What is an outdoor edger?

These tools provide a vertical cut into the soil, to create a clean line between a lawn and a flowerbed, driveway, sidewalk or some other structure.... More »

Besides a miter joint, is there another type of joint that I can use to make a wooden frame?

Yes. You can also use a butt joint with pocket screws or with... More »

How long of a nail should I use?

If the board you are fastening to another is not going to bear weight, it should be a half inch longer than the board is thick. If it is going to... More »

How can you check to see if an old square is still accurate?

Simply find a straight edge and make a mark at 90 degrees. Then flip the square over and make another mark next to your first mark. If the two lines... More »

I need to find the exact center of a circle. What’s the best square to use?

A framing square is the proper tool. Place the corner of the square anywhere on the circle’s edge. Then mark where the tongue and the blade... More »

What are all the markings on my framing square used for?

They consist of rafter tables, which are used to figure lengths and cuts of rafters, and the Essex Board Measure table, which shows board... More »

I need to cut a lot of 2x material for a project I’m working on. What type of square should I use?

A speed square is probably your best option. It has a flange on one side that buts up to the edge of the board to allow making square marks. It can... More »

« back to project
 
 

Comments (0)